ESC Commands

ESC Commands

HT

HT
Name	Horizontal tab
Format	ASCII HT Hex 09 Decimal 9
Description	Move the print position to the next tab position. If no tab position is set (it is default setting), this command will be ignored The tab position is set by ESC D If the tab position exceeds the print area, printing position will be moved to the starting position of next line (Considering as a line is full, print the data and feed one line).
Reference	ESC D

LF

LF
Name	Print and feed paper
Format	ASCII LF Hex 0A Decimal 10
Description	Print the data in the printer buffer, then feed paper for one line according to the current line space settings. After printing, the print position moves to the beginning of the line.
Reference	ESC 2，ESC 3

CR

CR
Name	Carriage return
Format	ASCII CR Hex 0D Decimal 13
Description	Adjust the print position to the starting position of this line and line feed.
Reference	LF

ESC SP n

ESC SP n
Name	Set the right-side character space
Format	ASCII ESC SP n Hex 1B 20 n Decimal 27 32 n
Description	Set the right right-side character space is [n×0.125mm] For double width mode, the character right margin is double than normal mode. The command will not effective to Chinese characte
Default	n=0

ESC ! n(Ⅰ)

ESC ! n
Name	set the font type
Format	ASCII ESC ! n Hex 1B 21 n Decimal 27 33 n
Description	Set the font type (italic, border, bold, double width, double height, inverse or underline). And the bit definitions of parameter n are shown as follows table
Reference	ESC -, ESC E, GS !
Default	n=0

ESC ! n（Ⅱ）

Bit	On/off	Hex	Decimal	Function
0	off	00	0	Character type A (12×24)
0	on	01	1	Character type B (9×17)
4	off	00	0	Double-height mode off
4	on	10	16	Double-height mode on
5	off	00	0	Double-width mode off
5	on	20	32	Double-width mode on
7	off	00	0	Underline mode off
7	on	80	128	Underline mode on

• If set double-width and double-height at the same time, quadrupled thecharacter size.
• Can not underline the blank generated by HT or the rotate 90 character.
• The width of under line set by ESC -, have not affected by the character size.
• ESC M also can set character type.
• ESC – also can turn on/off underline.
• GS ! also can set character size.

ESC $ nL nH

ESC $ nL nH
Name	Set the absolute print position
Format	ASCII ESC $ nL nH Hex ESC $ nL nH Decimal 27 36 nL nH
Parameter Range	0≤nL≤255 0≤nH≤255
Description	Moves the print position to a location in a distance of (nL + nH × 256) dots from the starting position for printing
Reference	ESC \

ESC * m nL nH

ESC * m nL nH d1...dk
Name	Select bit-image mode
Format	ASCII ESC * m nL nH d1...dk Hex 1B 2A m nL nH d1...dk Decimal 27 42 m nL nH d1...dk
Parameter Range	m = 0,1,32,33 0≤nL≤255 0≤nH≤3 0≤d≤255
Description	Stores the bit image data in the print buffer using the mode specified by bit image mode m, nl and nh specifies a bit image in the horizontal direction as(nl+256×nh) dots, [d]k specifies the bit image data (column format) k indicates the amount of bit image data, but it does not need to be transmitted..
Note	If m is out of Parameter Range, the nL and the other data will regard as the normal data. If the bit image exceeds one line of print area, the excess part will be Ignored. Data [d]k specifies a bit printed to 1 and not printed to 0. Bold, double-strike, underline, character size, upside-down, black/white command will not affect to the command.

ESC - n

ESC - n
Name	Turn underline mode on/off
Format	ASCII ESC - n Hex 1B 2D n Decimal 27 45 n
Description	Turns underline mode on or off using n as follows if n= 0 or 48, Turns off underline mode if n=1 or 49, Turns on underline mode (1-dot thick) if n=2 or 50, Turns on underline mode (2-dots thick)
Note	Can not underline the blank generated by HT or the rotate 90 character. Default width is 1-dot thick. The thick is not affected by the character size. ESC ! can also turn on/off underline.
Default	n=0
Reference	ESC !

ESC 2

ESC 2
Name	Set the line space to a default value 3mm
Format	ASCII ESC 2 Hex 1B 32 Decimal 27 50
Description	Set the line space to a default value 3mm(24×0.125mm)
Reference	ESC 3

ESC 3

ESC 3
Name	Set the line space to n dots
Format	ASCII ESC 3 n Hex 1B 33 n Decimal 27 51 n
Description	ASet the line space to n dots
Default	n=24
Reference	ESC 2

ESC SO

ESC SO
Name	Turn on double width mode
Format	ASCII ESC SO n Hex 1B 0E n Decimal 27 14 n
Parameter Range	0≤n≤255
Description	Turn on double width mode
Note	Use LF or ESC DC4 to turn off
Default	n=2

ESC DC4

ESC DC4
Name	Turn off double width mode
Format	ASCII ESC DC4 n Hex 1B 14 n Decimal 27 20 n
Parameter Range	0≤n≤255
Description	Turn off double width mode
Default	n=2
Note	The value of n is same with the n in turn on command

ESC @

ESC @
Name	Initialize the printer
Format	ASCII ESC @ Hex 1B 40 Decimal 27 64
Description	Reset the printer, the print mode reset to the default setting
Note	Can not clear the data in receive buffer

ESC B

ESC B
Name	Set the left margin
Format	ASCII ESC B n Hex 1B 42 n Decimal 27 66 n
Parameter Range	0≤n≤47
Description	Set the left margin
Note	This command just affects the character, doesn’t affect the Chinese
Default	n=0

ESC D

ESC D
Name	Set horizontal tab positions
Format	ASCII ESC D n1...nk NUL Hex 1B 44 n1...nk 00 Decimal 27 68 n1...nk 0
Parameter range	1≤n≤255 0≤k≤32
Description	Set the horizontal tab positions, the meanings of parameters are as follows: n1..nk are horizontal tab position (Unit: 8 dots), NULL is a stop character
Note	Horizontal tab position stored as a data, the data value is [character width×n] measured from the line begin. When this command is used, any previous horizontal tab settings will be canceled. The tab position can be switched by HT command The max set value is 32(k=32), larger than 32, the larger data will regard as normal data. Transmit [d]k in ascending order and place a NULL code at the end. When dk is less than or equal to dk-1, horizontal tab setting is finished, and the following data will be processed as normal data. ESC D NUL will cancel the horizontal tab position. Even the character width change, the set tab position will not change.
Defualt	Default tab position is character type A(12×24), the eight character space (column 9,17,25 ...)
Reference	HT

ESC E

ESC E
Name	Turn bold mode on/off
Format	ASCII ESC E n Hex 1B 45 n Decimal 27 69 n
Parameter range	0≤n≤255
Descriptiopn	Turns bold mode on or off using n as follows: If n = 0, turn off the bold, if n = 1, turn on the bold.
Default	n = 0
Reference	ESC !

ESC J

ESC J
Name	Print and feed paper for n dots
Format	ASCII ESC J n Hex 1B 4A n Decimal 27 74 n
Parameter range	0≤n≤255
Description	Print the data in the printer buffer and feed paper for n dots(0.125mm per dot)
Note	After printing, the print position moves to the beginning of the line. This has not affected the set value by ESC 2 or ESC 3.

ESC G

ESC G
Name	Print and feed paper
Format	ASCII ESC G n Hex 1B 47 n Decimal 27 71 n
Parameter range	0≤n≤255
Description	Turn double-strike mode on/off: 0: turn off double-strike 1: turn on double-strike。
Note	The double-strike has the same print with bold print
Default	n=0
Reference	ESC E

ESC M

ESC M
Name	Select the character type
Format	ASCII ESC M n Hex 1B 4D n Decimal 27 77 n
Parameter range	n = 0,1,48,49
Description	Select character type: If n=0 or 48,Character type A (12×24) If n=1 or 49,Character type B (9×17)
Reference	ESC!

ESC R

ESC R
Name	Select international character
Format	ASCII ESC R n Hex 1B 52 n Decimal 27 82 n
Parameter range	0≤n≤255
Description	Selects an international character set n as follows:: n=0 refer to U.S.A n=1 refer to France n=2 refer to Germany n=3 refer to U.K. n=4 refer to Denmark I n=5 refer to Sweden n=6 refer to Italy n=7 refer to Spain I n=8 refer to Japan n=9 refer to Norway n=10 refer to Denmark II n=11 refer to refer to Spain II n=12 refer to Latin America n=13 refer to Korea n=14 refer to Slovenia/Croatia n=15 refer to China n=16 refer to Vietnam n=17 refer to Arabia n=101 refer to ISO-8859-1 n=102 refer to ISO-8859-2 n=103 refer to ISO-8859-3 n=104 refer to ISO-8859-4 n=105 refer to ISO-8859-5 n=107 refer to ISO-8859-7 n=109 refer to ISO-8859-9 n=113 refer to ISO-8859-13 n=115 refer to ISO-8859-15 n=130 refer to GB13030-2000
Default	n=0(Suggest to use n >100)

ESC V

ESC V
Name	Turn 90° clockwise rotation mode on/off
Format	ASCII ESC V n Hex 1B 56 n Decimal 27 86 n
Parameter range	n = 0,1,48,49
Description	Turn 90° clockwise rotation mode on/off using n as follows: If n=0 or 48, Turns off 90°clockwise rotation mode If n=1 or 49, Turns on 90°clockwise rotation mode
Note	Underline is not effective for the rotation characters
Default	n=0
Reference	ESC !，ESC -

ESC \

ESC \
Name	Print and feed paper
Format	ASCII ESC \ nL nH Hex 1B 5C nL nH Decimal 27 92 nL nH
Parameter range	0≤nL≤255 0≤nH≤255
Description	Moves the print position to a location in a distance of (nL + nH × 256) dots from the current position
Note	If the position is not in print area, the set will be ignored. If the set position is in right of the current position, the distance N is nL+nH ×256=N If the set position is in left of the current position, the distance N is: nL+nH×256=65536-N
Reference	ESC $

CR

LF
Name	Print and feed paper
Format	ASCII CR Hex 0D Decimal 13
Description	Adjust the print position to the starting position of this line and line feed.
Reference	ESC 2，ESC 3

CR

LF
Name	Print and feed paper
Format	ASCII CR Hex 0D Decimal 13
Description	Adjust the print position to the starting position of this line and line feed.
Reference	ESC 2，ESC 3

CR

LF
Name	Print and feed paper
Format	ASCII CR Hex 0D Decimal 13
Description	Adjust the print position to the starting position of this line and line feed.
Reference	ESC 2，ESC 3